Kiteboarding

src: thekitebar.com

Kiteboarding is a surface water sport combining aspects of wakeboarding, snowboarding, windsurfing, surfing, paragliding, skateboarding and sailing into one extreme sport. A kiteboarder harnesses the power of the wind with a large controllable power kite to be propelled across the water on a kiteboard similar to a wakeboard or a small surfboard, with or without footstraps or bindings.

Kitesurfing is a style of kiteboarding specific to wave riding, which uses standard surfboards or boards shaped specifically for the purpose.

There are different styles of kiteboarding, including freestyle, freeride, downwinders, speed, course racing, wakestyle, jumping and kitesurfing in the waves. In 2012, the number of kitesurfers was estimated by the ISAF and IKA at 1.5 million persons worldwide (pending review). The global market for kite gear sales is worth US $250 million.

Video Kiteboarding

History

In the 1800s, George Pocock used kites of increased size to propel carts on land and ships on the water, using a four-line control system--the same system in common use today. Both carts and boats were able to turn and sail upwind. The kites could be flown for sustained periods. The intention was to establish kitepower as an alternative to horsepower, partly to avoid the hated "horse tax" that was levied at that time. In 1903, aviation pioneer Samuel Cody developed "man-lifting kites" and succeeded in crossing the English Channel in a small collapsible canvas boat powered by a kite

In the late 1970s, the development of Kevlar then Spectra flying lines and more controllable kites with improved efficiency contributed to practical kite traction. In 1978, Ian Day's "FlexiFoil" kite-powered Tornado catamaran exceeded 40 km/h.

In October 1977 Gijsbertus Adrianus Panhuise (Netherlands) received the first patent for KiteSurfing. The patent covers, specifically, a water sport using a floating board of a surf board type where a pilot standing up on it is pulled by a wind catching device of a parachute type tied to his harness on a trapeze type belt. Although this patent did not result in any commercial interest, Gijsbertus Adrianus Panhuise could be considered as the originator of KiteSurfing.

Through the 1980s, there were occasionally successful attempts to combine kites with canoes, ice skates, snow skis, water skis and roller skates.

Throughout the 1970s and early 1980s, Dieter Strasilla from Germany developed parachute-skiing and later perfected a kiteskiing system using self made paragliders and a ball-socket swivel allowing the pilot to sail upwind and uphill but also to take off into the air at will. Strasilla and his Swiss friend Andrea Kuhn used this invention also in combination with surfboards and snowboards, grasskies and selfmade buggies. One of his patents describes in 1979 the first use of an inflatable kite design for kitesurfing.

Two brothers, Bruno Legaignoux and Dominique Legaignoux, from the Atlantic coast of France, developed kites for kitesurfing in the late 1970s and early 1980s and patented an inflatable kite design in November 1984, a design that has been used by companies to develop their own products.

In 1990, practical kite buggying was pioneered by Peter Lynn at Argyle Park in Ashburton, New Zealand. Lynn coupled a three-wheeled buggy with a forerunner of the modern parafoil kite. Kite buggying proved to be popular worldwide, with over 14,000 buggies sold up to 1999.

The development of modern-day kitesurfing by the Roeselers in the USA and the Legaignoux in France carried on in parallel to buggying. Bill Roeseler, a Boeing aerodynamicist, and his son Cory Roeseler patented the "KiteSki" system which consisted of water skis powered by a two line delta style kite controlled via a bar mounted combined winch/brake. The KiteSki was commercially available in 1994. The kite had a rudimentary water launch capability and could go upwind. In 1995, Cory Roeseler visited Peter Lynn at New Zealand's Lake Clearwater in the Ashburton Alpine Lakes area, demonstrating speed, balance and upwind angle on his 'ski'. In the late 1990s, Cory's ski evolved to a single board similar to a surfboard.

In 1996, Laird Hamilton and Manu Bertin were instrumental in demonstrating and popularising kitesurfing off the Hawaiian coast of Maui while in Florida Raphaël Baruch changed the name of the sport from flysurfing to kitesurfing by starting and promoting the first commercial brand of the industry "Kitesurf".

In 1997, the Legaignoux brothers developed and sold the breakthrough "Wipika" kite design which had a structure of preformed inflatable tubes and a simple bridle system to the wingtips, both of which greatly assisted water re-launch. Bruno Legaignoux has continued to improve kite designs, including developing the bow kite design, which has been licensed to many kite manufacturers.

In 1997, specialized kite boards were developed by Raphaël Salles and Laurent Ness. By the end of 1998 kitesurfing had become an extreme sport, distributed and taught through a handful group of shops and schools worldwide. The first competition was held on Maui in September 1998 and won by Flash Austin.

Starting in 1999, kitesurfing became a mainstream sport with the entry of key windsurfing manufacturers namely Naish and Neil Pryde. Single direction boards derived from windsurfing and surfing designs became the dominant form of kiteboard. From 2001 onwards, twin-tip bi-directional boards became more popular for most flat water riders, with directional boards still in use for surf conditions.

In May 2012, the course racing style of kitesurfing was announced as a sport for the 2016 Rio Olympics, replacing windsurfing. However, after a vote by the General Assembly of ISAF in November 2012 (in Dun Laoghaire, Ireland) the RSX windsurfer was reinstated for both Men and Women this was an unprecedented decision when the constituent members of ISAF overthrew a decision made by the ISAF Council Kitesurfing remains therefore a non-Olympic sport until 2020 at the earliest. The ISAF mid-year meeting of May 2013 proposed seeking an eleventh medal to include kitesurfing in 2020 at the same time there was a commitment made to retain the existing other 10 classes as they are for 2020 and even 2024 including the RSX windsurfer for men and women.

Kitesurfing was named as an official event at the 2018 Summer Youth Olympics in Buenos Aires.

Jump records (height, length, time)

Nick Jacobsen achieved the world record for the highest kite jump measured by WOO Sports on February 19, 2017 in Cape Town, South Africa, during a session with 40-knot winds. Jacobsen's jump reached 28.6 meters high, with an airtime of 8.5 seconds.

Speed records

French kitesurfer Sébastien Cattelan became the first sailor to break the 50 knots barrier by reaching 50.26 knots on 3 October 2008 at the Lüderitz Speed Challenge in Namibia. On 4 October, Alex Caizergues (also of France) broke this record with a 50.57 knots run. Similar speeds are reached by windsurfers in the same location by Anders Bringdal and Antoine Albeau, respectively 50.46 and 50.59 knots. These speeds are verified, but are still subject to ratification by the World Sailing Speed Record Council. Earlier in the event, on 19 September, American Rob Douglas reached 49.84 knots (92.30 km/h), becoming the first kitesurfer to establish an outright world record in speed sailing. Previously the record was held only by sailboats or windsurfers. Douglas also became the world's third over-50 knots sailor, when on 8 September he made a 50.54 knots (93.60 km/h) run.

On 14 November 2009, Alex Caizergues completed another run of 50.98 knots in Namibia.

October 2010, Rob Douglas became the outright record holder for the short distance 500 meters with 55.65 knots. Sébastien Cattelan became the record holder of France and Europe with 55.49 and was the first rider to reach 55 knots.

On 13 November 2017, French rider Alex Caizergues became the new world speed record holder in France (Salin de Giraud) reaching 57.97 knots or 107.36 km/h.

Long distance

Notable journeys

Louis Tapper completed the longest recorded kite journey, completing 2000 km between Salvador and Sao Luis, Brazil. The journey was completed between July/August 2010 and took over 24 days of kitesurfing. This trip is also the longest solo journey, completed without support crew, using one kite and a 35-litre backpack .

The previous longest recorded kite journey was by Eric Gramond who completed a 13-day trip of 1450 km along the coast of Brazil.

Bering Strait crossing

Constantin Bisanz, a 41-year-old Austrian, crossed a 50-mile stretch of the Bering Strait embarking from Wales, Alaska on August 12th, 2011 at 4:00 am, and arriving in eastern most Russia two hours later, after which he returned by boat to Alaska. It occurred after 2 previously failed attempts, the first of which was on July 28th, 2011, in which an incident occurred where he found himself floating in 36 °F water with no board, kite or GPS unit for 1 hour before being rescued. On his second attempt on August 2nd, he and two friends sailed half the distance before turning around due to poor wind conditions.

Transatlantic crossing

A team of six kitesurfers, Filippo van Hellenberg Hubar, Eric Pequeno, Max Blom, Camilla Ringvold, Ike Frans, and Dennis Gijsbers crossed the Atlantic ocean, from the Canary islands to the Turks and Caicos Islands a distance of about 3,500 miles (5,600 km), from 20 November 2013, to 17 December 2013. Each of the six spent four hours each day surfing, broken into two sessions of two hours each, one during the day, and the other during the night.

Maps Kiteboarding

Governance

The International Kiteboarding Association (IKA) is an International Class Association of the International Sailing Federation (ISAF). Its responsibility, amongst others, is to manage the global administration of the sport and to combine world events into one united ranking. An Executive Committee is on a regular basis re-appointed by the class AGM. The duties and responsibilities of the Executive Committee are: to take care of the day-to-day business of the association. To consider and coordinate submissions from the sub-committees. The Executive Committee elected amongst themselves: - Chairman: Richard Gowers (GBR) - Vice-chairman: Bruno De Wannemaeker (BEL) - Executive Secretary: Markus Schwendtner (GER) - Board members: Mirco Babini (ITA), Olivier Mouragues (FRA), Adam Szymanski (POL) and John Gomes (USA).

There are also national and regional kitesurfing associations in many countries.

src: i.ytimg.com

Styles

Several different kitesurfing styles are evolving, some of which cross over.

src: www.kitesurfwallpaper.com

Techniques

Kitesurfing basics

Kiteboarding can pose hazards to surfers, beachgoers, bystanders and others on the water. Many problems and dangers that may be encountered while learning kiting can be avoided or minimized by taking professional instruction through lesson centers. Kitesurfing schools provide courses and lessons to teach skills including kite launching, flying, landing, usage of the bar, lines and safety devices.

Turning

A beginner can turn by stopping or sinking backwards into the water, and then turning the kite in the opposite direction and starting again. A 'heel turn jibe' is a quicker, and more skillful turn that is executed by slowing down, flattening the board, then reversing the board flat on the water by bringing the rear foot around downwind to eventually become the new leading foot. The direction of the kite is then reversed, which swings the surfer's path in a semi circle, centered on the kite. As the turn ends, the kite is flown over to be in front of the surfer again.

A poorly executed turn will "fly" the surfer, and is often followed by a tumble if the surfer can't put the board down at the right angle.

A careless turn in high winds can easily swing the rider into the air and result in an uncontrolled impact.

Controlled flying and jumping

Controlled flying is possible and is one of the biggest attractions of the sport. Before jumping, the surfer builds up tension in the lines by strongly edging the board. Then the kite is flown quickly to an overhead position, sometimes just as the surfer goes over a wave. As the kite begins to lift, the board edge is then 'released' and the rider becomes airborne. The kite is then piloted from overhead to the direction of travel. A large variety of maneuvers and tricks can be performed while jumping.

Board grabs

Board grabs are tricks performed while a rider is jumping or has gained air from popping by grabbing the board in a number of positions with either hand. Each grab has a different name dependent on which part of the board is grabbed and with which hand it is grabbed by. Rear hand grabs are known as Crail, Indy, Nuke, Tindy, Tail, Tailfish, and Stalefish; while front hand grabs are known as Slob, Mute, Seatbelt, Melan, Method, and Nose. Names generally originate from other board sports like skateboarding and snowboarding.

A number of grabs can also be combined into one trick. A rider may perform a tail grab going to indy by moving the rear hand from the back of the board to the middle of the toe side edge.

src: www.exploresquamish.com

Assessing the wind

Wind strength and kite sizes

Kitesurfers change kite size and/or line length depending on wind strength--stronger winds call for a smaller kite to prevent overpower situations. Kitesurfers will determine the wind strength using either an anemometer or, more typically, visual clues as shown in the Beaufort scale.

All modern kites dedicated to kitesurfing provide a "depower" option to reduce the power in the kite. By using depower, the kite's angle of attack to the wind is reduced, thereby catching less wind in the kite and reducing the power or pull.

Wind speed, rider experience and weight, board size, kite design and riding style are all interdependent and affect the choice of kite.

An experienced rider generally carries a 'quiver' of different sized kites appropriate for the wind speed range. A typical kite quiver might include 8 m², 10 m² and 12 m² traditional "C-kites". Exact kite sizes will vary depending on rider weight and desired wind ranges.

Bow kites have a wider wind range than C-kites, so two kite sizes (such as 7 m² and 12 m²) could form an effective quiver for winds ranging from 10 to 30+ knots for a 75 kg (165 lb) rider.

Wind direction

Cross-shore and cross-onshore winds are the best for kiteboarding. Offshore winds pose the danger of being blown away from the shore in the event of equipment failure or loss of control. Offshore winds are suitable in a lake or when a safety boat is available, however they are generally more gusty. Direct onshore winds carry the risk of being thrown onto land, and are thus less favorable.

src: newwindkiteboarding.com

Locations

Any location with consistent, steady side-onshore winds (10 to 35+ knots), large open bodies of water and good launch areas is suitable for kitesurfing. Most kitesurfing takes place along ocean shores, usually off beaches, but it can also be practiced on large lakes and inlets and occasionally on rivers. Since kiteboarding relies heavily on favorable, consistent wind conditions, certain locations tend to become popular and sought out by kiteboarders.

src: i.ytimg.com

Equipment

Power kites

A power kite is available in two major forms: leading edge inflatables and foil kites.

Leading edge inflatables

Leading edge inflatable kites, known also as inflatables, LEI kites, are typically made from ripstop polyester with an inflatable plastic bladder that spans the front edge of the kite with separate smaller bladders that are perpendicular to the main bladder to form the chord or foil of the kite. The inflated bladders give the kite its shape and also keep the kite floating once dropped in the water. LEIs are the most popular choice among kitesurfers thanks to their quicker and more direct response to the rider's inputs, easy relaunchability if crashed into the water and resilient nature. If an LEI kite hits the water or ground too hard or is subjected to substantial wave activity, bladders can burst or it can be torn apart.

In 2005, Bow kites (also known as flat LEI kites) were developed with features including a concave trailing edge, a shallower arc in planform, and frequently a bridle along the leading edge. These features allow the kite's angle of attack to be altered more and thus adjust the amount of power being generated to a much greater degree than previous LEIs. These kites can be fully depowered, which is a significant safety feature. They can also cover a wider wind range than a comparable C-shaped kite. The ability to adjust the angle of attack also makes them easier to re-launch when lying front first on the water. Bow kites are popular with riders from beginner to advanced levels. Most LEI kite manufacturers developed a variation of the bow kite by 2006.

Early bow kites had some disadvantages compared to classic LEI kites:

• They can become inverted and then not fly properly
• They can be twitchy and not as stable
• Heavier bar pressure makes them more tiring to fly
• Lack of "sled boosting" effect when jumping

In 2006, second generation flat LEI kites were developed which combine near total depower and easy, safe relaunch with higher performance, no performance penalties and reduced bar pressure. Called Hybrid or SLE kites (Supported Leading Edge), these kites are suitable for both beginners and experts.

In 2008, Naish introduced another kite design, with their "Sigma Series" of kites. These kites are a SLE design and feature a unique "bird in flight" shape with the center of the kite swept back to put much of the sail area behind the tow point, which Naish claims has multiple benefits.

In 2009, the performance revolution shows no sign of slowing. Bridled designs feel more like C kites, and five-line hybrids have better depower capability than ever before. There are more than thirty companies manufacturing Leading edge inflatable kites. The delta-kites are growing in popularity since 2008 with around 12 companies offering delta-kites since 2008/2009.

Between 2009 and 2013 kite technology has continued to grow. Kites have become lighter, more durable, much easier to launch and safer. Manufacturers have continued to add new safety features. This has resulted in a growing number of new riders, both younger and older. In 2013, there are at least 20 "major" kite manufacturers, each with multiple models available. Many of the manufacturers are on their third or fourth generation of kites.

Foil kites

Foil kites are also mostly fabric (ripstop nylon) with air pockets (air cells) to provide it with lift and a fixed bridle to maintain the kite's arc-shape, similar to a paraglider. Foil kites have the advantage of not needing to have bladders manually inflated, a process which, with an LEI, can take up to ten minutes. Foil kites are designed with either an open or closed cell configuration.

Open Cell

Open cell foils rely on a constant airflow against the inlet valves to stay inflated, but are generally impossible to relaunch if they hit the water, because they have no means of avoiding deflation, and quickly become soaked.

Closed Cell

Closed cell foils are almost identical to open cell foils except they are equipped with inlet valves to hold air in the chambers, thus keeping the kite inflated (or, at least, making the deflation extremely slow) even once in the water. Water relaunches with closed cell foil kites are simpler; a steady tug on the power lines typically allows them to take off again. An example for a closed cell kite is the Arc Kite.

Kite sizes

Kites come in sizes ranging from 0.7 square meters to 21 square meters, or even larger. In general, the larger the surface area, the more power the kite has. Kite power is also directly linked to speed, and smaller kites can be flown faster in stronger winds. The kite size--wind speed curve tapers off, so going to a larger kite to reach lower wind ranges becomes futile at a wind speed of around eight knots. Kites come in a variety of designs. Some kites are more rectangular in shape; others have more tapered ends; each design determines the kite's flying characteristics. 'Aspect ratio' is the ratio of span to length. High aspect ratios (ribbon-like kites) develop more power in lower wind speeds.

Seasoned kiteboarders will likely have three or more kite sizes which are needed to accommodate various wind levels, although bow kites may change this, as they present an enormous wind range; some advanced kiters use only one bow kite. Smaller kites are used by light riders, or in strong wind conditions; larger kites are used by heavier riders or in light wind conditions. Larger and smaller kiteboards have the same effect: with more available power a given rider can ride a smaller board. In general, however, most kiteboarders only need one board and one to three kites (7-12 sq m in size).

Other equipment

• Flying lines are made of a strong material such as ultra-high-molecular-weight polyethylene, to handle the dynamic load in unpredictable wind while maintaining a small cross-sectional profile to minimize drag. They come in lengths generally between seven and thirty-three meters. Experimentation with line lengths is common in kiteboarding. The lines attach the rider's control bar to the kite using attachment cords on the kite edges or its bridle. Most power kites use a 3, 4 or 5-line configuration. The 5th line is used to aid in re-launching or adjusting the kite's angle of attack.
• The control bar is a solid metal or composite bar which attaches to the kite via the lines. The rider holds on to this bar and controls the kite by pulling at its ends, causing the kite to rotate clockwise or counter-clockwise like a bicycle. Typically a chicken loop from the control bar is attached to a latch or hook on a spreader bar on the rider's harness. Most bars also provide a quick-release safety-system and a control strap to adjust the kite's angle of attack. Kite control bars, while lightweight and strong, are usually heavier than water; "bar floats" made of foam may be fixed to the lines right above the harness to keep the bar from sinking if lost in the water. Control bars are usually specific to a particular kite type and size and are not usually suitable for use with different kite types.
• A kite harness comes in seat (with leg loops), waist, or vest types. The harness together with a spreader bar attaches the rider to the control bar. The harness reduces the strain of the kite's pull from the rider's arms, spreading it across part of the rider's body. This allows the rider to perform jumps and other tricks while remaining attached to the kite via the control bar. Waist harnesses are the most popular harnesses among advanced riders, although seat harnesses make it possible to kitesurf with less effort from the rider, and vest harnesses provide both flotation and impact protection. Kite harnesses resemble windsurfing harnesses, but with different construction; a windsurfing harness is likely to fail when used for kiteboarding.

• Kiteboard, a small composite, wooden, or foam board. There are now several types of kiteboards: directional surf-style boards, wakeboard-style boards, hybrids which can go in either direction but are built to operate better in one of them, and skim-type boards. Some riders also use standard surfboards, or even long boards, although without foot straps much of the high-jump capability of a kite is lost. Twin tip boards are the easiest to learn on and are by far the most popular. The boards generally come with sandal-type footstraps that allow the rider to attach and detach from the board easily; this is required for doing board-off tricks and jumps. Bindings are used mainly by the wakestyle riders wishing to replicate wakeboarding tricks such as KGBs and other pop initiated tricks. Kiteboards come in shapes and sizes to suit the rider's skill level, riding style, wind and water conditions.

• A wetsuit is often worn by kitesurfers, except in warmer conditions with light winds. When kitesurfing in strong winds, body heat loss is reduced by wearing a wetsuit. A "shortie" is worn to protect the torso only, and a full suit is used for protection against cool conditions, from marine life such as jellyfish, and also from abrasions if the rider is dragged by the kite. Dry suits are also used to kitesurf in cold conditions in winter.
• A safety hook knife is considered required equipment. The corrosion resistant stainless steel blade is partially protected by a curved plastic hook. It can be used to cut entangled or snagged kite lines, or to release the kite if the safety release system fails. Some kitesurfing harnesses are equipped with a small pocket for the knife.
• A helmet is often worn by kitesurfers to protect the head from blunt trauma. Helmets prevent head lacerations, and can also reduce the severity of impact injuries to the head, as well as compression injuries to the neck and spine.
• A personal flotation device or PFD may be required if the kitesurfer is using a boat or personal water craft for support. It is also recommended for kitesurfing in deep water in case the kitesurfer becomes disabled and must wait for rescue.
• An impact vest provides some protection against impacts to the torso area. They can also provide some flotation.
• A board leash that attaches the board to the kitesurfer's leg or harness is used by some riders. However, many kitesurfing schools discourage the use of board leashes due to the risk of recoil, where the leash can yank the board to impact the rider, which can result in serious injury or even death. Generally, kitesurfers that use a board leash will also wear a helmet to help protect against this.
• Signaling devices are useful if the kitesurfer needs to be rescued. This may be as simple as a whistle attached to the knife, or retro-reflective tape applied to the helmet. Some kitesurfers carry a mobile phone or two-way radio in a waterproof pouch to use in an emergency. A small Emergency Position-Indicating Radio Beacon (EPIRB) can be carried and activated to send out a distress signal.
• A buddy is important to help with launching and retrieving the kite, and to assist in an emergency.
• A GPS can be used to measure distance travelled, tracks and speed during a session.

src: www.worldkiteboardingleague.com

Dangers and safety

Power kites are powerful enough to pull the rider like a boat in wakeboarding and to lift their users to diving heights. An uncontrolled kite can be dangerous, especially in difficult environments. A rider can lose control from falling or from sudden wind gusts, which can occur in the presence of strong winds from squalls or storms ("collard").

It is possible to be seriously injured after being lofted, dragged, carried off, blown downwind or dashed, resulting in a collision with hard objects including sand, buildings, terrain or power lines or even by hitting the water surface with sufficient speed or height ("kitemare", a portmanteau of kite and nightmare). Adequate quality professional kiteboarding training, careful development of experience and consistent use of good judgement and safety gear should result in fewer problems in kiteboarding.

Weather

Weather forecasting and awareness is the principal factor to safe kiteboarding. Lack of weather awareness and understanding figures in many of these cases, but avoiding weather problems is possible Choice of inappropriate locations for kiteboarding where the wind passes over land creating wind shadow, rotor with pronounced gusts and lulls has also factored in many accidents. Paying attention to the weather and staying within the limits of the riders ability will provide the safest experience. Kitesurfing storm fronts can be particularly dangerous due to rapid changes in wind strength and direction.

Aggravating factors

Lack of a sufficient downwind buffer distance between the kiter and hard objects has contributed to accidents reducing the available distance and time for reaction. Jumping and being airborne at inappropriate places such as shallow water or near fixed or floating objects can be hazardous. Collisions with wind surfers, other kite boarders or water craft are hazards, particularly at busy locations.

Solo kiteboarding has been a frequent contributing cause to accidents; kiteboarders should try to kite with friends and keep an eye on one another. A kitesurfer can get farther from shore than an easy swim, which is the primary reason kitesurfing in directly offshore winds is discouraged. Marine hazards include sharks, jellyfish, sea otters, dolphins, and even crocodiles, depending on the location. Drowning has been a factor in severe accidents as well and may have been avoided in some cases through the use of an appropriate flotation aid or impact vest and development of acceptable swimming skills.

Equipment

Some kite designs from late 2005 and onwards have included immediate and almost full depower integrated with the control bar and improved quick release mechanisms, both of which are making the sport much safer. However, lack of sufficient practice of emergency depowering the kite and going out in excessively strong or unstable weather can reduce the benefit of high depower kites. A safety knife is useful if lines become tangled and dangerous.

Statistics

Accidents can generate serious injuries or even be deadly. 105 accidents were reported in the Kiteboarding Safety Information Database between 2000 and September 2003, with 14 fatalities. In South Africa between October 2003 and April 2004, 83% of search & rescue missions involving kitesurf were in offshore winds with the kite still attached to the harness, uncontrolled in strong winds or impossible to relaunch in weak winds. On 30 missions, there was no fatalities but five injuries : two had bone fractures after being hit by their boards, two others were suffering from critical hypothermia and exhaustion and the fifth was exhausted and lacerated.

Advances in hybrid and bow kite designs leads to a better ability to control the power that they provide and effective safety release systems. In 2003, fatality ratings for the U.S. stated that 6 to 12 kiteboarders died for 100'000 participants. This being higher than 4 to 5 in SCUBA diving (and much higher than the two Walkers), comparable to the 15 in Motor Vehicle Traffic, and 56 for Paragliders.

Reports of casualties

• "Stuart man, 38, identified as kite surfer killed by sharks off Stuart Beach". Palm Beach Post. 4 February 2010. 
• "Kitesurfer, 70, killed at remote beach". WA Today. 6 February 2012. 
• "Kite surfer killed at Redcliffe". Brisbane Times. 6 March 2012. 
• "Dante Torres, Malibu Kite Surfer Dies in Tragic Kelp Accident". LA Weekly Blogs. 13 March 2012. 
• "Phuket beach toll rises as kitesurfing American dies". Phuket Gazette. 31 May 2012. 
• "Kiteboarder killed at Cheney Lake identified". KWCH-TV. 6 August 2012. 
• "Sean Sands: Hunstanton kite surfing death 'accidental'". BBC. 6 July 2015. 
• "Mark Paxton: Southend kitesurfer has died in a freak accident at Ray Creek, Point Clear, Clacton". Clacton Gazette. 21 February 2016. 

Kitesurfing safety rules

Some countries have laws about flying kites and being safe while flying that may also apply to kitesurfing.

Kite High Rule - A kiter who is upwind (closest to the wind) must keep their kite high to avoid their lines crossing those of downwind kiters. Similarly, the downwind kiter must keep their kite low to avoid their lines crossing upwind kites. This applies regardless of whether kiters are on the same, or opposing courses.

Clearance Rule - A kiter while jumping must have a clear safety zone of at least 50m downwind because they will move downwind during the jump. A rider must also have a clear safety zone of 30m upwind to jump as his lines could touch the kite or the lines of another rider kiteboarding close by (see Kite High rule). It's important to also consider potential hazards downwind and crosswind of the rider such as people, buildings, trees and other fixed obstacles.

Kiters are also considered as sailing vessels - so some standard sailing rules apply such as:

Starboard Rule When kiters approach from opposite directions the kiter who has the wind on the starboard (right side, right leg/arm leads in direction of travel) has right of way. The kiter who has the wind on the port side (left side, left leg/arm are leads in direction of travel) shall keep out of the way of the other. In simple terms, this means "keep right" with the kiter coming in the opposite direction passing on the left.

In sailing terms, a sailor or kiter with right of way is entitled to "insist" on exercising that right (warning opposing kiters) by shouting "starboard" clearly and in good time.

Other boating rules such as no-go zones, distance from shore and swimmers also apply.

src: mauikiteboardinglessons.com

Terminology and jargon

• Air time: the amount of time spent in the air while jumping. This can be remarkably long; the record is Jesse Richman's 22 second long jump. Five to ten seconds is not unusual.
• Apparent wind: the kite's speed relative to the surrounding air. When kitesurfing in a straight line, the kite's apparent wind is a combination of the wind speed and the speed of the kite and rider over the surface, but since the kite is highly steerable apparent wind can vary widely depending on how the kite is being flown. Most ways of increasing power from the kite involve giving it a higher apparent wind somehow, i.e. diving the kite, riding faster, or riding at a greater angle into the wind. Any of these raises the kite's apparent wind speed.
• Back Stall: A condition in which the kite ceases to move forward through the air and becomes difficult to control, often resulting in the kite flying backwards and crashing. Back stall is often caused by lack of wind or by flying the kite with too great of an angle of attack.
• Big Air: performing a high jump utilizing the lift of the kite. The jump is often assisted in its initial stage by the rider being catapulted off the lip of a wave.
• Body dragging: being pulled through the water without standing on a board. This is an early step in the learning process, and is recommended before trying the board after flying a trainer kite.
• Boost: to suddenly become airborne
• Brain Fart: to forget what trick you intended to perform mid air and end up crashing or landing on the water.
• Charlie browner: same as kiteboarder or kitesurfer.
• Chicken loop: a hard rubber loop attached to the middle line which has been fed through the control bar. It is used to attach the control bar to the harness so the kitesurfer can produce tension in the lines using their entire bodyweight instead of using purely arm strength.
• Chicken bone/chicken finger/donkey dick: a hard rubber "tongue" attached to the chicken loop which the rider feeds through the spreader bar hook to prevent the rider from becoming "unhooked".
• De-power: to reduce the kite's power (pull), generally by adjusting the angle of attack of the kite. Most kites and control bars now allow a rider to rig a kite for a number of different power levels before launching, in addition to powering the kite up and down "on the fly" by moving the bar up and down. Depowerability makes a kite safer and easier to handle. Some new kite models, especially "bow" kites, can be de-powered to practically zero power, giving them an enormous wind range.
• DP: dawn patrol; an early morning session.
• downwind: the direction the wind is blowing towards; to leeward. When a rider is facing downwind the wind is at their back.
• Downwinder: a kitesurfing "trip" (could actually be as short as a few minutes) where the rider starts at one point and ends up at another point downwind of their original position.

• Edge: tilting the board with its edge into the water. Used to control the direction of travel. Learning to edge properly is critical for learning to tack upwind. Edging is one of the fundamental skills of kitesurfing and is one of the ways kitesurfing is different from windsurfing or wakeboarding. While windsurf boards have daggerboards and/or skegs to steer the board upwind while lift and planing is provided by the board itself, generally kiteboards actually combine both functions and the bottom of the board lifts the rider and steers simultaneously. Kiteboard fins are generally much smaller and are for keeping the board in the water (see "tea-bagging"), but are not essential. Because kite boards have a small rocker, a deep edge can allow the board to act as a large low drag fin. Edging in wakeboarding is used for steering the board; whereas in kite boarding not only does edging steer the kite board, it is essential for kite control and controlling board speed. Riding downwind towards the kite subtracts massively from the kite's power and helps control board speed as well.
• Facial: total loss of flying kite control while on the beach, resulting in the harnessed rider being dragged face first downwind across rocks and sand.
• Freeride: kiteboarding style. Plain kiteboarding that does not involve tricks or jumping. The main goal is keeping a good edge and ability to traverse upwind. This would normally require a board with little rocker.
• Freestyle: kiteboarding style. Freestyle involves tricks (or combinations of tricks) where the rider is jumping off the water and experiencing enhanced elevation using lift generated from the kite. Freestyle is, weather-wise, a multi-condition concept and is to some degree equipment-specific. "Big air" is commonly associated with freestyle.
• Goofy: the footedness of the rider, with the right foot leading.
• Guinea pig a person who goes out to test if the wind is rideable or not. If it is, others start riding too. Also known as a Wind-dummy.
• Heel side: the side of a board on the edge where a rider's heels are (opposite of toe side). "Riding heel side" is riding with heels down.
• Hindenburg: (a reference to the Hindenburg Airship disaster of 1937) a kite falling out of the air due to the loss of tension in the control lines, and therefore the loss of kite control. Hindenburging can be caused either by lack of wind or by the kite advancing to a position upwind of the kitesurfer in the wind window, also called "overflying the kite".
• Handlepass: while unhooked, passing the control bar behind a riders back while in the air.
• Hot Launch: recovering and launching the kite from a position deep inside the wind window so the kite is immediately under maximum power (potentially dangerous).
• Kiteloop: is a powered group of tricks where a rider loops the kite through the power zone.
• Kitemare: a kiteboardsurfing accident or dangerous mishap. Kitemares can be deadly.
• Launch: getting the kite in the air. The kite may be launched assisted or unassisted. An assisted launch is generally safer than an unassisted launch.
• Lofted: to get lifted vertically into the air by the kite due to a strong gust of wind. Being lofted has resulted in fatalities when kiters on or near land were dragged into obstacles. The danger can be avoided by minimizing time on land with the kite flying directly overhead, and by not kiting in overpowered situations.
• Luff : when the air flow stalls around the kite. It may then stall and fall out of the sky. Like sails, a luffing kite has rippling and flapping panels. When launching the kite, if the kite is luffing, the rider should move farther upwind, or the person holding the kite should move downwind.
• Mobe: this term has two meanings: either a class of wakestyle tricks involving an invert with a 360-degree spin or a specific trick involving a back roll with a frontside 360 handlepass (while keeping the kite below 45 degrees). The former meaning stems from the latter, which was the first type of mobe to ever be landed. Other types of mobes include: mobe 540, mobe 720, slim chance, KGB, crow mobe, moby dick, Pete Rose, blind pete, crow mobe 540, etc.
• Nuking: wind blowing at great speeds (30-40 knots). These extreme conditions are dangerous for most riders.
• Offshore: wind blowing at the water from the shore. Never ride in offshore winds without some means of recovery, i.e. a chase boat. This is somewhat less important in smaller bodies of water, of course.
• Onshore: wind blowing perpendicular to and directly at the shore from the water. A challenging condition for beginners, especially if waves are present.
• Dookie Dive: loss of power during air time resulting in a crash into the water.
• O-Shit Loop: two loops on either ends of the bar that are attached to the kite lines and run through rings attached to the bar. A standard leash attachment point.
• Overhead waves: waves two or more meters (6 ft) from trough to crest;
• Overpowered: the condition of having too much power from the kite. Can be a result of an increase in wind, incorrect kite choice (too large for the conditions), incorrect adjustment, simply going too fast, etc. Interestingly, experienced riders who are overpowered can switch to a smaller board to compensate, to a degree, although it's common to have just one board.
• pop: height gained above the water using only the board and tension in the lines to get lift, with the kite usually positioned at 45 degrees. Lower kite angles are possible for more experienced riders. Used as a basis for many tricks and regarded as an essential skill for progressing.
• Port the left side of a ship, as perceived by a person on board facing the bow (front).
• Power up: when the kite's power increases (suddenly), because of wind gusts or the kite's movement.
• Power zone: is the area in the sky where the kite generates the most lift (pull), this is generally between 0 and 60 degrees arc from the center of the downwind direction.
• Re-Launch: a general term for getting the kite back up in the air after crashing it (on land or water). A relaunch is unassisted and requires the rider to follow a kite-specific procedure (check the manual). As years of development have gone by, the more recent kites are easier to relaunch.
• Self Rescue: a maneuver by which a rider with a downed kite manipulates the kite in the water to assist them in swimming back to shore. The rider generally wraps up their lines until they reach their kite, then positions their kite so that it is on its back as it would be carried on land but with the wing-tip closer to shore catching the wind. This wing tip acts as a sail and helps pull the rider to shore. This is considered an important maneuver to learn.
• Send it: to move the kite aggressively up through the power zone.
• Schlogging: this is riding extremely underpowered. A rider has no power to plane and definitely not enough to jump. A rider and their board bounce from planing on the surface to being dragged in the water.
• Shit hot: the art of stylish smooth moves.
• SLE: Supported Leading Edge. A C shaped kite with an inflatable leading edge, currently the most advanced kite design available allowing massive de-power.
• Side offshore: wind blowing between sideshore and at a 45-degree angle away from the shore.
• Side onshore: wind blowing between sideshore and at a 45-degree angle towards the shore.
• side shore: winds blowing parallel to the shore. Usually the most desirable direction for kitesurfing.
• Spreader bar: a stainless steel bar that attaches to the rider's harness. It has a hook that holds the "chicken loop" when riding hooked in.
• Starboard the right side of a vessel as perceived by a person on board facing the bow (front).
• Stomp: to successfully perform a trick.
• Surfstyle: Wave riding using surfboards. Ideal conditions are cross shore to cross offshore with the wind blowing in the same direction that the wave is breaking. Boards can be ridden with or without foot straps.
• Tack: the direction which is being sailed, normally either starboard tack or port tack. In a starboard tack the wind is coming in from the rider's starboard (right-hand) side, similar to sailing a boat. In normal riding, the kitesurfer takes a heading which is as close to into the wind as possible, and in any event leads at some angle slightly upwind, sometimes as much as 45 degrees; jumping or wave riding usually results in traveling downwind, so the net result is to maintain relative position. Alternatively, see "downwinder".
• Tea-bagging: popping out of and falling back into the water intermittently due to light or gusty wind, poor flying skills, twisted lines etc.
• Toe side: the side of a board on the edge where a riders toes are (opposite of heel side). "Riding toe side" is riding with toes down.
• Underpowered: the condition of having insufficient power from the kite. Can be a result of insufficient wind, choosing a kite that is too small for the wind, rigging incorrectly, board too small, water current in the same direction as the wind, not riding fast enough, etc. A rider who is continuously diving the kite and sending it back up in a sine-wave pattern is usually underpowered.
• Unhooked is when a kitesurfer is riding while the chicken loop is not attached to the rider's harness.
• Upwind: the direction from which the wind is blowing; windward; into the wind.
• VaS conditions: Victory at Sea; rough sea conditions characterized by overhead wind waves causing severe shore break.
• Wakestyle: A style of kiteboarding in which the rider usually uses wakeboarding (or kiteboarding) "boots" for their kiteboard (as opposed to straps and pads), ensuring their feet remain firmly attached at all times (hense the term "Wakestyle"). This style is also associated with performing powered tricks with the kite as low to the water as possible (something generally perceived by kiteboarders to be more difficult and stylish).
• Walk of Shame is the act of walking back upwind to the location where the kite was originally launched.
• Wind-dummy a person who goes out to test if the wind is rideable or not. If it is, others start riding too. Also known as a Guinea pig.
• Wind window is the 120- to 180-degree arc of the sky downwind of the rider in which the kite can be flown. Roughly one fourth of a sphere's surface. If the rider is facing downwind on a flat surface, like the ocean, the wind window consists of roughly all the area the rider can see, from the rider's peripheral vision on one side, along the horizon to the other side, and then directly overhead back to the first side. If the rider somehow puts the kite out of the window--for example, by riding downwind too quickly and sending the kite directly overhead and behind, the kite will stall and often fall out of the sky.
• Zenith the location in the wind window directly over the kiter's head. This is the neutral position where kitesurfers can place the kite to stop moving or prior to movement. This places the kite in a more vulnerable to "Hindenburgs" position than any other.

src: www.wbur.org

Kiteboarding versus windsurfing

src: static1.squarespace.com

World Champions of Freestyle

Sanctioned Tours (PKRA/VKWC/WKL):

MAN:

• 2017 - Carlos Mario Bebe
• 2016 - Carlos Mario Bebe
• 2015 - Liam Whaley
• 2014 - Christophe Tack
• 2013 - Alex Pastor
• 2012 - Youri Zoon
• 2011 - Youri Zoon
• 2010 - Andy Yates
• 2009 - Kevin Langeree
• 2008 - Aaron Hadlow
• 2007 - Aaron Hadlow
• 2006 - Aaron Hadlow
• 2005 - Aaron Hadlow
• 2004 - Aaron Hadlow
• 2003- Martin Vari
• 2002-
• 2001- Martin Vari

WOMAN:

• 2017- Bruna Kajiya
• 2016- Bruna Kajiya
• 2015- Gisela Pulido
• 2014- Karolina Winkowska
• 2013- Gisela Pulido
• 2012- Karolina Winkowska
• 2011- Gisela Pulido
• 2010- Gisela Pulido
• 2009-Bruna Kajiya
• 2008- Gisela Pulido
• 2007- Gisela Pulido
• 2006- Kristin Boese
• 2005- Kristin Boese
• 2004-
• 2003- Cindy Mosey
• 2002- Cindy Mosey

src: i.ytimg.com

Gallery

src: www.northkiteboarding.com

See also

src: i.ytimg.com

References

src: cdn.shopify.com

External links

• Kitesurfing links at Curlie (based on DMOZ)
• Kitesurfing Associations at Curlie (based on DMOZ)

Source of the article : Wikipedia